Specifications:

• +200A load (PCB tested to +400A).
• Volt 12 & 24 Volt.
• Active volt 5.7-32-volt DC.
• Minimum St.by current consumption – 2.3 mA.
• Weight: 543 Gram.
• Box Size 183x119x21.
• Box Type: Anodized Aluminum.
• Connectors AMPSEAL .
• Connector part number: 23pin: 770680-1 / 35pin:776164-1  / Gold Pins 770520-3.

23 High power Outputs can be controlled/monitored up to 7 levels:

• Overload.
• Load to Low.
• Short Circuit.
• Open Wire.
• Active Status.
• Error.
• Current Reading.

16 Low power Outputs can be controlled/monitored up to 5 levels:

• Overload.
• Short Circuit.
• Open Wire.
• Active Status.
• Error.

 1 Output:

• Failure and Reset input/output. – Lamp / Switch.

 12 Inputs:

• Toggle/momentary/latch.
• Negative Input.
• Positive Input.
• Analog Input.
• Pulse Input (PWM) max. 2Khz.

Outputs General:

• High side (+ Output).
• Low side (Gnd. Output).
• PWM 10hz -2Khz (Pulse).

52 CAN Inputs:

• 125kbit/s to 1.33 Mbit/s.
• 11bit Identifier.
• 29bit Identifier.
• Fully configurable CAN.

Extra Features:

• Flash upgrade only with USB Connected.
• Special Menu “Blink Keypad” "Greyhill" and "HP9642".
• Password Protection.
• Debug Terminal Optional.

  CAN Export:

• 5 Levels of CAN Export.
• Fully Configurable CAN Export.
• All Status´s export- Inputs, Outputs, Current, Status, Virtual.
• Failures, Open Wire, Current, Temperature, PWM Status.
• Firmware and S/N and more.

 Special Functions:

• CAN Monitor Build in - Logger.
• Flash Timers.
• Delay Timers.
• PWM.
• Kill output function.
• Start output Function.
• Wiper Parking and logic.
• Virtual (Logical Inputs).
• Error Log.
• Auto Reset Fuse.
• Sequence Functions.
• Automatic Power Down.
• CAN Export of all statuses, inputs, outputs, current use, virtual, failure states.
• Failure Output with Reset.

 8 Sequence Options:  

• Set/Reset.
• Toggle (Off -> A –> Off).
• 3 Step Single (Off -> A - > B –> Off).
• 4 Step Single (Off -> A - > B -> C –> Off).
• 3 Step add (Off -> A -> A+B -> Off).
• 4 Step add (Off -> A -> A+B -> A+B+C -> Off).

 20 Delay Timers:

• On delay 0,1-1500 seconds.
• On Time 0,1-6000 seconds.
• Can be set in 5 groups also.

 5 Flash Timers:

• Flash on-time 0,01-25 Sec.
• Flash Off-time 0,01-25 Sec.

20 Virtual Channels:

• It is possible to define some logical signals.
• Based on And / Or /Nand / Nor and delay signals.

 Warranty:

• 2 Years + Lifetime*
• * Maximum 15 years

 Software Updates:

• Free of charge.
• PC Software - Free

  Regarding Current load of the Connector: AMPSEAL is specified to 17A Per Pin at 125 degrees Celsius. We have tested the current load with a temperature of 80 degree Celsius Each pin can have a load of 25A without any problems- For a load of 35A per pin its ok for 2 minutes Inrush is measured to be ok for 50A / 10 sec. In case of higher load, use double pin output or more.